Kawasaki ZX-10R Forum banner

1 - 6 of 6 Posts

·
Registered
Joined
·
1 Posts
Discussion Starter #1
Hi everyone. This is my first post here, so I apologize if this is in the wrong section, or this has been answered before.

I am a new owner of a 2016 zx10r, I put about 700 miles on it so far. I upgraded from my 2008 zx6r, and i love it.

So today, i installed an integrated tail light. While doing this, i removed my battery. When I finished installing the tail light, i put the battery back in, but i may have messed up the connection because i blew a fuse. Easy fix, i installed a new fuse and the bike started no problem.

However, the engine light, as well as the caution light came on. The tail light works fine, and the bike still runs amazing, but everything on the display screen continues to flash.

I did read you can clear this error, but how do i know i dont have a bigger problem? But like i said, the bike runs great.

It might be worth mentioning that a week ago i installed a k and N filter. But that was a week ago and I have had no problems until i was finished with the tail light installation (today).

Well, i hope someone can lead me in the right direction.

Thanks,
Sean
 

·
Registered
Joined
·
718 Posts
Hi everyone. This is my first post here, so I apologize if this is in the wrong section, or this has been answered before.

I am a new owner of a 2016 zx10r, I put about 700 miles on it so far. I upgraded from my 2008 zx6r, and i love it.

So today, i installed an integrated tail light. While doing this, i removed my battery. When I finished installing the tail light, i put the battery back in, but i may have messed up the connection because i blew a fuse. Easy fix, i installed a new fuse and the bike started no problem.

However, the engine light, as well as the caution light came on. The tail light works fine, and the bike still runs amazing, but everything on the display screen continues to flash.

I did read you can clear this error, but how do i know i dont have a bigger problem? But like i said, the bike runs great.

It might be worth mentioning that a week ago i installed a k and N filter. But that was a week ago and I have had no problems until i was finished with the tail light installation (today).

Well, i hope someone can lead me in the right direction.

Thanks,
Sean
Literally no way to know till you pull the code and see what its telling you is wrong
 

·
REPOST Enforcement Mod
Joined
·
13,561 Posts
:welcome:

As Victors so aptly put it, no one can help you until you pull the FI code causing the error. And there's also no way to reset the light until the problem is fixed and the ignition goes through several cycles and it stays fixed for 10 minutes after you let it idle for more than 30 seconds, then ride it more than 25mph for more then 5 minutes. Then turn it off and do it all again 3 times. Woohoo!

And why would you pull the battery out when changing the taillight that plugs and unplugs? :eek:
 

·
Registered
Joined
·
2 Posts
Hi Everyone
My bike having a same issues, the check engine light keep showing and the rpm dash light also not running when I turned the key ON. Bike can start as usual and can run as normal.
Anyone can give me with the valuables advice
Thanks Wan
 

·
Registered
Joined
·
2 Posts
Hi Everyone
My bike ZX10R Gen 5 having a same issues, the check engine light keep showing and the rpm dash light also not running when I turned the key ON. Bike can start as usual and can run as normal but the check engine light keep showing.
Anyone can give me with the valuables advice
Thanks Wan
 

·
REPOST Enforcement Mod
Joined
·
13,561 Posts
Hi Everyone
My bike having a same issues, the check engine light keep showing and the rpm dash light also not running when I turned the key ON. Bike can start as usual and can run as normal.
Anyone can give me with the valuables advice
Thanks Wan
If the instrument cluster doesn't finish the complete self-test properly, then you have a problem with the cluster itself.
 
1 - 6 of 6 Posts
Top