Kawasaki ZX-10R Forum banner

pcv

  1. Yoshi 3/4 + PCV = 1st gear bog? (Gen 4)

    Performance and Tech
    Guys, 2014 ZX-10R Here. What's happening is that in first gear from a take off the damn thing doesn't want to go anywhere. It's terrible. I'm pretty sure that it's super flat/no pull in the top range as well but I have only gone up there once during my test ride. It starts up and idles just...
  2. Gen 4: 2011-2015 SC Project Fuel Map for PCV

    Performance and Tech
    I am hoping that someone here can help me. I just purchased a SC Project CRT slip on w/ link pipe to de-cat the bike, a servo buddy module, and a PCV. Lots of $$$ spent and i really don't want to have to spend even more money having it put on a dyno. My elevation is close to sea level. Does...
  3. Gen 4: 2011-2015 pcv settings with m4 street slayer and maybe air filter.

    Performance and Tech
    I was looking through the possible maps for the pcv and didnt find any for the m4 street slayer. I also don't have an air filter but I was gonna get one if I heard good things about adding one over stock. Total mods are -1/+2, ivans wire mod, m4 street slayer, pcv. Does anybody have a similar...
  4. Gen 4: 2011-2015 power commander V or.....?

    Performance and Tech
    My buddy has a zx14 and was told that a pcv was a waste of money because it didn't add much hp and in some cases even lost hp. Does anynody have any good/bad experiences with a pcv or any suggestions? Currently the bike has m4 street slayer slip on, ivans wire mod, -1+2 sprockets, and maybe a...
  5. Gen 4: 2011-2015 m4 gp slip on ok by itself??

    Performance and Tech
    Hey guys. So I'm really wanting exhaust cuz I just hit 1k miles yesterday and stock exhaust sounds like ass imo. I like the m4 gp sound (I think it looks a little bit cheap but oh well) but I'm also a little low on cash. I have the money for the slip on but my buddy said to wait until I have the...
  6. O2 Optimiser on Aus Gen4 - to buy or not to buy?

    Performance and Tech
    Hi guys, New to the forums. I've got a 2012 ZX10R (Aus model). Long story short, I prematurely bought a PCV and a yoshi 3/4 R77 without realising the issues involved with o2 sensors etc. After reading up a bit on the forums, the general consensus seems to be that: 1. you can't run the aussie...
  7. Gen 4: 2011-2015 Dynojet Power Commander V for GEN 3 & GEN 4 ZX10R for $279

    Riders Discount
    RidersDiscount.com has now has in stock 2011-2013 ZX10R PCV ready to ship! Supply is limited, so call Mike at 866.931.6644 ext 804 or send an email to FORUM at RIDERSDISCOUNT dot COM with PCV 2011 ZX10R in the subject line and we’ll get back to you right away. These are on sale for $279 with...
  8. Two Brothers Juice Box

    Riders Discount
    The Juice Box from Two Brothers Racing provides easy engine tuning with plug and play installation that’s designed to improve the drivability of your motorcycle. A model-specific wire harness allows anyone with basic tools to install this fuel controller and start programming fuel delivery on...
  9. zx-10r 2009 running jerky

    The ZX-10R
    My bike: a zx-10r 2009. My modifications: removed secondary butterflies, racefit growler slip on, k&n air filter and PCV with customized map (no autotune) My problem: I just finished a 2000 km long trip to northern Thailand and the bike ran smooth and great all the time. Before leaving this...
  10. '08 zx10r Arata + PCV o2 sensor problem code67

    The ZX-10R
    Hello guys, I have recently fit a PCV (I am not planning on putting an autotune) And just now a Arata Ti system. For the system I have disconnected the 2 o2 sensors therefore I have a Fi light on with code 67 for it (is there a way of eliminating this)? I am planning to have a custom map made...
  11. Dynojet AutoTune for Power Commander V

    Riders Discount
    Designed to compliment any bike with a Power Commander V already installed, the Autotune Wideband O2 Controller from Dynojet uses the same software employed on Dynojet’s dynamometers that trained professionals use to build custom maps. No more trips to the dyno required, just install the...
  12. PCV - Who can help with this phenomenon?

    The ZX-10R
    Hi! After installing PVC & Autotune on my ZX10r 08 (european) and some acceptations of the autotune trims the bike goes better than before. BUT: Gear 1...4 are ok. Only with gear 5 & 6 and only in the low rev / low thottle area the bike starts to bog and shows hard load changes. it seems...
  13. How-To: Clean Install of a PC5 (PCV) on your 2008-2009 ZX-10

    The ZX-10R
    Alright I can't find them online, but the instructions provided for the PCV by Dynojet are pretty good, but the suggested mounting location sucks. They recommend you set the power commander in the trunk (under passenger seat) basically just sitting there, with the wires coming out of it facing...
Top