Kawasaki ZX-10R Forum banner

Search results

1-20 of 312 Results
Advanced Search
  1. Dash flashing after dyno run

    The ZX-10R
    There's a certain riding sequence to get that to reset, from one wheel moving and not the other, maybe can reset with woolich I never tried
  2. Gen 4 Secondary throttle flies

    Wanted: Buy or Trade
    I have them but don't have screws. They are the same flies used in gen 3
  3. 2014 ZX10R, A Question About Timing

    The ZX-10R
    The exhaust cam looks off to me. Gen 4 is a real pain to do in the bike. I make lots of marks on everything with a marker before disassemble, I would retime it again. You also have to set it like a tooth or so off to compensate for tightening down the cams. It'll line up if done right
  4. Favorite/best street tire of 2019?

    Performance and Tech
    I've been legitimately over 200mph on a road 5 with zero traction issues, I also ride through flooded roads and winter roads with no issues, a sport touring tire is better than a pure sport tire for a bike that gets ridden on the street for many reasons including faster warm up time and more, I...
  5. Favorite/best street tire of 2019?

    Performance and Tech
    Road 5 is my choice for any street bike, if your a track rider maybe something else but you won't out ride a road 5 on the street
  6. gen4 to gen5

    The ZX-10R
    With the Gen 5 arm im running 18/40 and wheelbase almost 57.5"
  7. Clutch Issues

    Performance and Tech
    If they are sticking while hot I'd suggest replacing the steels, and if the fiber are old replace them also. I've seen both warp when hot and be OK when cold, face curve edge of steels inward
  8. Clutch Issues

    Performance and Tech
    Are you sure plates aren't sticking, I've seen steels warp when hot and get better when cold also
  9. gen4 to gen5

    The ZX-10R
    Do you think you will have a decent gain from the Gen 5 head on Gen 4 block? I've been debating on what to do to my Gen 4 next
  10. Gen 3: 2008-2010 ECU Fuse Keeps Blowing !!!!

    The ZX-10R
    I've seen shorted pair valve cause that also
  11. All new 2020 CBR 214hp @ 14.5k rpm

    General Motorcycle Discussions
    how much does your gen 4 weigh? I've got mine at 388lbs fully street legal with 3 gal of fuel. One of the lightest bikes I've built
  12. Clutches

    The ZX-10R
    Kg clutch kit is affordable and works well for every bike I've used them in
  13. Clutch Basket issue?

    The ZX-10R
    Where are you from
  14. Clutch Basket issue?

    The ZX-10R
    Welding the rivets is cheap and easy
  15. Broken Sprint

    The ZX-10R
    I also have pics of quite a few of my airboxes after riding through rain, snow, dirt and construction with sprint filters and its clean as can be. The install makes all the difference
  16. Broken Sprint

    The ZX-10R
    No reason to pull the head just pull the throttle bodies off if you wanna go digging, I've seen plastic like that stuck in a jeep intake port for a long time. Eventually held the valve open and had no compression. Took piece out and ran fine.
  17. Broken Sprint

    The ZX-10R
    Sprint is the only filter I've ever noticed actual top end gain, and I've tried almost everything on the market
  18. Broken Sprint

    The ZX-10R
    Never seen that before, don't think there's any way the motor ate that. Too big, maybe stuck in ram air
  19. Gen 1: 2004-2005 Ecu flash

    The ZX-10R
    Depends how the cam was degreed etc. Doing this wrong could lose you power instead of gain
  20. Gen 3: 2008-2010 Good Maps

    Welcome Newbies!
    I do at my shop but I'm not set up for bench flashing yet. I do them on the bike as they come to me, my area isn't very popular for guys wanting to spend the money on tuning etc unfortunately
1-20 of 312 Results
Top