Kawasaki ZX-10R.net - View Profile: gaz
  

gaz gaz is offline

Track Day Rider

  Visitor Messages

Showing Visitor Messages 1 to 5 of 5
  1. michael4012
    04-24-2019 12:45 AM - permalink
    michael4012
    Jim, im looking at a G4 1157 build, iv done 2 G3 builds using JE pistons 4mm strokers & =3mm bore, there a single ring piston because the pin is raised 2mm. Do you know of any other manufactures making similar pistons?
  2. michael4012
    03-30-2019 01:51 AM - permalink
    michael4012
    Hi mate i just sent you e/mail with some pictures.
  3. F 18 driver
    09-26-2018 08:32 PM - permalink
    F 18 driver
    Hi GAZ

    I'm in a bit of a tight spot. I wonder if I can request some help and insight from you

    My secondary throttle body sensor was pulled out of the socket and I'd like to replace it without replacing the entire throttle body.

    I see on eBay that they sell the secondary throttle body sensors… Do you know or can you please explain to me how to adjust it after I purchased it.

    I have adjusted TBS sensors before my Hayabusa…but I don't know how to do it on the 2006 zx10R

    Please help I'm desperate.

    Thanks very much.

    Q
  4. F 18 driver
    09-17-2018 06:53 AM - permalink
    F 18 driver
    hello and good morning gaz

    I hope you had a very nice relaxing weekend

    My forks are leaking so I have to change the seals…

    Do you have any recommendation as to where to buy the seals from and what oil to use?

    I'd like to save a few bucks if possible

    Thank you very much.

    Your friend,

    Q
  5. Capncalyx
    11-22-2017 02:49 PM - permalink
    Capncalyx
    Glad you still are on the forum, the stuff you share is gold man. Too bad you had to make a new screen name. Happy Turkey Day from Indiana.

  About Me

  • About gaz
    Biography
    formerly gazx10 here
    Location
    monroe ga.
    Interests
    retired racing benn building engines 35 years
    Bike:
    07 zx10 street/strip bike

  Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: 05-19-2019 11:23 AM
  • Join Date: 08-23-2017
  • Referrals: 0

  Friends

Showing Friends 1 to 1 of 1

  Mentions

No results to display...

  Quotes

05-02-2019
07:44 PM - Disney Hook quoted gaz in post Bike won't start after maintenance
fresh fuel pump always g...
04-18-2019
10:28 AM - SpazOnaZX quoted gaz in post C3L1CA's Street/Strip Wanna Be Build Thread
first thing, the main th...
09:36 AM - C3L1CA quoted gaz in post C3L1CA's Street/Strip Wanna Be Build Thread
I wish you were close by...
04-15-2019
04:51 PM - EvokedPotential quoted gaz in post Simple engine build
every aftermarket piston...
04-10-2019
12:25 PM - C3L1CA quoted gaz in post C3L1CA's Street/Strip Wanna Be Build Thread
I always measure at 1mm ...
08:23 AM - C3L1CA quoted gaz in post C3L1CA's Street/Strip Wanna Be Build Thread
U have found 247,5 cause...
04-02-2019
03:09 PM - ShawnG quoted gaz in post Thinner kit head gasket
static compression and r...
03-31-2019
07:50 PM - zx racer quoted gaz in post Spark or Fuel
check throttle sync, ck ...
03-27-2019
07:29 AM - C3L1CA quoted gaz in post C3L1CA's Street/Strip Wanna Be Build Thread
im cheap, m8x1.25 x1.5 i...
03-26-2019
10:37 PM - michael4012 quoted gaz in post need a good complete set of gen 2 intake/ex valves
...rk also. For you Gaz, no problem at all i...
03-21-2019
08:34 PM - giovannidc quoted gaz in post '04 engine noise
sounds like a rod, will ...
02-20-2019
10:13 PM - michael4012 quoted gaz in post Long time, building another land speed Gen 2
most powersport fuel pum...
02-14-2019
10:40 PM - ablaz3d quoted gaz in post gen 1 race int/race ex cams
set on ebay for $200, in...
02-11-2019
05:18 PM - Boxtradamus quoted gaz in post Gen1 Supercharger
... springs used. Boy gaz, you have learned a ...
01-28-2019
06:23 AM - Bikeman1000 quoted gaz in post Shooting Flames
don guhl just answered t...
01-25-2019
06:33 PM - Kawigreen05ZX10 quoted gaz in post Cams
read ur previous posts, ...
01-16-2019
11:19 AM - ddipaola quoted gaz in post Shooting Flames
disabling pair valve wit...
12-25-2018
08:10 PM - TheRoadWarrior quoted gaz in post Thinner Head Gasket with Pump Gas?
cast pistons won't like ...
12-24-2018
10:56 AM - SpazOnaZX quoted gaz in post Thinner Head Gasket with Pump Gas?
cast pistons won't like ...
11-29-2018
02:28 PM - gaz quoted SpazOnaZX in post Thinner Head Gasket with Pump Gas?
As long as you don't rattle it...
 
For the best viewing experience please update your browser to Google Chrome