Kawasaki ZX-10R Forum banner

Reaction score
331

Marketplace Rating
(5.0 - 58 reviews)

Profile posts Latest activity Discussions Buy & Sell Reviews About

  • · Registered
    Joined
    ·
    7 Posts
    Hi Garth,

    Noticed you mentioned you have the 2016+ service manual...
    Any chances to get a link/email?

    Would really appreciate it. :)

    WR

    · Registered
    Joined
    ·
    217 Posts
    Hey man I know you seem to have the service manuals for a lot of bikes. I'm wondering if you one for the 89 ninja 500 ex? Thanks!!

    · Registered
    Joined
    ·
    44 Posts
    "I have the service manual if anyone needs it."

    Do you have an electronic copy? If so do you mind emailing me a copy? Thanks.
    My email is howardcamp80@gmail.com.

    · Registered
    Joined
    ·
    0 Posts
    What up? hoping to get a download Gen 5 manual. Kind of 911 due to crazy deadline. Racebike with ECU flash, only runs in safe mode and then stalls out, it is pretty crazy. You could send the file or dropbox link to kevinnolde@cox.net. Thanks

    · Registered
    Joined
    ·
    0 Posts
    Hi,

    Do you have a copy of the service manual on pdf? If so I would love to get a copy of it. Glad to paypal you a few bucks for the trouble. Thanks!

    · Registered
    Joined
    ·
    145 Posts
    Hey Garth,


    Gen4 base circles as I see them are as follows:
    Stock intake = 28.06
    Stock exhaust = 26.22
    Kit Intake = 28.06
    Kit Exhaust = 26.28 (weird)


    Arshag

    · Registered
    Joined
    ·
    864 Posts
    Hi garth285
    As you said a stock head gasket on the zx-10r is 0.60 mm or so, if I want a 0.45 mm I just remove the middle part of a stock gasket and go.

    O.K I understand well that the stock gaskethave pins or something to joint the 3 parts together so to remove the central part I need to break this little thing, soo now I got the 2 outside part of the gasket I ditch the middle part. Now to make that two parts stay together what I do (to let the holes aligned), Put the two outside parts put a little glue and put back the gasket in place or it doesn't matter because the two dowell pin who are on the block will aligne it AWY.

    I got some question about porting too, but doesn't want to bother you too much.

    Thanks.

    · Registered
    Joined
    ·
    8 Posts
    I'm having serious problems with my gen 1. I replaced the clutch and cable and assembled as followed fiber, anti-chatter, fiber, steel, fiber, steel, fiber, steel, fiber etc but clutch slips bad. First gear just revs and doesn't catch at all. I'm using new ebc kit. I have adjusted the cable at the lever and at the bottom

    · Registered
    Joined
    ·
    128 Posts
    Gday. Any thoughts on advancing a gen four intake. .50 gasket decked race ecu. Thanks Lyndon

    · Registered
    Joined
    ·
    128 Posts
    Gday I'm Lyndon. You seem in the know. My gen 4. .50 gasket. Valve job. Race ecu etc. 112 104 std cams. Any thoughts advancing the intake say 2 to 4 degrees and the exhaust ???. Thanks Lyndon

    · Registered
    Joined
    ·
    116 Posts
    Any way you can call me? I run zx engine in small dirt cars. Got some cam questions I do not want out on the net!!!

    Bryan
    936 526 4175

    · Registered
    Joined
    ·
    269 Posts
    garth man still waiting on the tracking number for the
    cams.... i racing intake and the 2 stock camshafts
    valves...
    valve springs and kawasaki racing valve springs i had sent to you via ebay
    3rd gen retainers from brandon
    and the thin head gasket


    said a while a go you were going to mail it off with tracking number like i suggested earlier if you want to just pay me out for everything im more than willing to take that instead the whooooole situation is dragging on waaaay toooooo looong

    · Registered
    Joined
    ·
    269 Posts
    i need the head mailed to carpenter motors by friday i mine as well just let them go ahead and have them do the work i need the money in my paypal no later than sunday please im running out of time and options and knowing carpenter they probably are seriously swamped with work so im going to have to wait even longer to have the head back but i dont have anybody else that i know can do the work

    · Registered
    Joined
    ·
    269 Posts
    race gasket
    1 intake camshafts
    1 racing intake camshaft
    1 exhaust camshaft
    8 kawasaki racing valve springs
    16 zx10r valve springs
    16 3rd gen retainers from brandon Andrews

    · Registered
    Joined
    ·
    1,355 Posts
    Hi Garth, I’m told you have done a lot of speed runs on your gen4.
    Can you tell me aprox what top speed I should hit with a -1 front sprocket?
    And how about going back to stock gearing, would it be just about 200mph?

    Not sure if you saw my dyno thread http://www.zx-10r.net/forum/showthread.php?t=202786
    but my gen4 is at 187hp and here are the mods:
    - Yoshimura ¾ slip-on
    - DynoJet Power Commander V
    - ECUleashed flash
    - BMC race airfilter
    - and the Rifleman throttle mod

    I appreciate your time
    Terry

    · Registered
    Joined
    ·
    86 Posts
    hey where did you get your wheels man? they are pure amazing. and how much did they run you? did you need to change out the bearing size or anything?
  • Loading…
  • Loading…
  • Loading…
  • Loading…
  • Loading…
Top