Kawasaki ZX-10R.net - View Profile: gaz

gaz gaz is offline

Track Day Rider

  Visitor Messages

Showing Visitor Messages 1 to 6 of 6
  1. Kemonric Davery Littl
    06-19-2019 06:21 AM - permalink
    Kemonric Davery Littl
    Do you still build bike's what's the best way to get in touch with you. Intrested in building a Gen 2 zx10 for street/strip
  2. michael4012
    04-24-2019 12:45 AM - permalink
    Jim, im looking at a G4 1157 build, iv done 2 G3 builds using JE pistons 4mm strokers & =3mm bore, there a single ring piston because the pin is raised 2mm. Do you know of any other manufactures making similar pistons?
  3. michael4012
    03-30-2019 01:51 AM - permalink
    Hi mate i just sent you e/mail with some pictures.
  4. F 18 driver
    09-26-2018 08:32 PM - permalink
    F 18 driver
    Hi GAZ

    I'm in a bit of a tight spot. I wonder if I can request some help and insight from you

    My secondary throttle body sensor was pulled out of the socket and I'd like to replace it without replacing the entire throttle body.

    I see on eBay that they sell the secondary throttle body sensors… Do you know or can you please explain to me how to adjust it after I purchased it.

    I have adjusted TBS sensors before my Hayabusa…but I don't know how to do it on the 2006 zx10R

    Please help I'm desperate.

    Thanks very much.

  5. F 18 driver
    09-17-2018 06:53 AM - permalink
    F 18 driver
    hello and good morning gaz

    I hope you had a very nice relaxing weekend

    My forks are leaking so I have to change the seals…

    Do you have any recommendation as to where to buy the seals from and what oil to use?

    I'd like to save a few bucks if possible

    Thank you very much.

    Your friend,

  6. Capncalyx
    11-22-2017 02:49 PM - permalink
    Glad you still are on the forum, the stuff you share is gold man. Too bad you had to make a new screen name. Happy Turkey Day from Indiana.

  About Me

  • About gaz
    formerly gazx10 here
    monroe ga.
    retired racing benn building engines 35 years
    07 zx10 street/strip bike


Total Posts
Visitor Messages
General Information
  • Last Activity: 07-22-2019 04:42 PM
  • Join Date: 08-23-2017
  • Referrals: 0


Showing Friends 1 to 1 of 1


No results to display...


07:21 AM - Boxtradamus quoted gaz in post No start. Fuel injectors not firing
...them all. Well done gaz.
08:14 AM - michael4012 quoted gaz in post Afr
u cannot fill small bott...
07:44 PM - Disney Hook quoted gaz in post Bike won't start after maintenance
fresh fuel pump always g...
10:28 AM - SpazOnaZX quoted gaz in post C3L1CA's Street/Strip Wanna Be Build Thread
first thing, the main th...
09:36 AM - C3L1CA quoted gaz in post C3L1CA's Street/Strip Wanna Be Build Thread
I wish you were close by...
04:51 PM - EvokedPotential quoted gaz in post Simple engine build
every aftermarket piston...
12:25 PM - C3L1CA quoted gaz in post C3L1CA's Street/Strip Wanna Be Build Thread
I always measure at 1mm ...
08:23 AM - C3L1CA quoted gaz in post C3L1CA's Street/Strip Wanna Be Build Thread
U have found 247,5 cause...
03:09 PM - ShawnG quoted gaz in post Thinner kit head gasket
static compression and r...
07:50 PM - zx racer quoted gaz in post Spark or Fuel
check throttle sync, ck ...
07:29 AM - C3L1CA quoted gaz in post C3L1CA's Street/Strip Wanna Be Build Thread
im cheap, m8x1.25 x1.5 i...
10:37 PM - michael4012 quoted gaz in post need a good complete set of gen 2 intake/ex valves
...rk also. For you Gaz, no problem at all i...
08:34 PM - giovannidc quoted gaz in post '04 engine noise
sounds like a rod, will ...
10:13 PM - michael4012 quoted gaz in post Long time, building another land speed Gen 2
most powersport fuel pum...
10:40 PM - ablaz3d quoted gaz in post gen 1 race int/race ex cams
set on ebay for $200, in...
05:18 PM - Boxtradamus quoted gaz in post Gen1 Supercharger
... springs used. Boy gaz, you have learned a ...
06:23 AM - Bikeman1000 quoted gaz in post Shooting Flames
don guhl just answered t...
06:33 PM - Kawigreen05ZX10 quoted gaz in post Cams
read ur previous posts, ...
11:19 AM - ddipaola quoted gaz in post Shooting Flames
disabling pair valve wit...
08:10 PM - TheRoadWarrior quoted gaz in post Thinner Head Gasket with Pump Gas?
cast pistons won't like ...
For the best viewing experience please update your browser to Google Chrome