TRE Mod - Kawasaki ZX-10R.net
 
LinkBack Thread Tools Display Modes
post #1 of 2 Old 01-07-2005, 05:48 PM Thread Starter
Orange you glad I'm a whore?
 
jeech's Avatar
 
Join Date: Oct 2004
Location: Roswell, GA
Posts: 11,028
Posting Frequency
   
Quote:
Originally Posted by Rattler
I can't remember where I saw it, I did think it was here!!! But I've done a full search and its showed up nothing.

I do seem to remember it being in official instructions, so I've pm'd Ivan and am awaiting a response.

I thought that it was in response to some issues that some had experienced when fitting the mod and that someone (Ivan I thought??) had provided updated fitting instructions to ensure that the TRE worked effectively.

Could have been just me drunk again though!!!

Thanks for your help guys.

Tim

Here you go Rattler......

You will need a T25 Security Torx bit (one with the cutout in the head) to complete step 5. The best way to accomplish is to use a 1/4 inch wrench on the bit to loosen the 2 screws. You do not need to remove the screws completely, but just loosen. Once the the 2 screws are loose, the entire assembly slides forward like it's on a pivot point.

The directions were a little unclear for me, but it makes sense once you loosen the screws.

Ivan's(www.ivansperformanceproducts.com)
TIMING RETARD ELIMINATOR*- Part # TRE-006 (2004 ZX-10R) *(patent pending)


Please read and understand all of these instructions before installing this product !!
(you may waste your time as well as our’s by not reading them)

1) Remove fuel tank & airbox

2) Locate GPS connector at bottom of fuel rail on left (green 4 wire connector) and release from fuel
rail. (you will need to depress the release tang)

3) Separate connector and remove the 2 wires (green w/red stripe and black) from the female end of
the connector (the end with the male pins)
You will need a sharp pointed implement to depress the latches that hold the pins into the
connector.

4) Install the pins that were removed from the stock connector into the supplied connector.
a) When installed correctly, you will hear a click when they seat.
b) Pay attention to their orientation as they will only fit when in the proper position.
(if you force them they will get damaged)
c) It does not matter which side of our connector the green/red or black wires are installed on.

5) While airbox is off, locate the sub-throttle sensor….
(controls secondary throttle plates, located just to the right of throttle cables, 3 wire sensor)
Loosen security torx screws (you will need a T25 bit with hole in center) and rotate sensor fully counter-clockwise (towards front of motorcycle)
Re-tighten screws.
If sensor adjustment is not done, bike will have softer Full Throttle response between 3000 and 5000 rpm
Stock sensor readings just for reference:
(readings need to be taken from sensor terminals - not wires- with sensor unplugged!!)
Blue/White – Brown/Black 1.09K ohm
Blue/White – Blue 4.16K ohm
Brown/Black – Blue 5.13K


DO NOT CONNECT TO ANY OTHER CONNECTOR ON MOTORCYCLE !!!

6) Plug in the T.R.E. and re-install the airbox and fuel tank.

To get the very best results, re-mapping is recommended, but not necessary.

This unit may be used in conjunction with the Dynojet Power Commander.
(recommended when aftermarket exhaust is used)

7) Enjoy your improved driveability!!
And remember........ I designed this product for you, to make your ride more enjoyable.

Thank you for your purchase !!
Ivan

Technical questions - 845-268-1212

**We offer substantial discounts on aftermarket exhausts and EFI systems and can provide you with a complete exhaust and fuel delivery package that will greatly improve the performance of your motorcycle which is as plug and play as you can get.**

Use of this product may not comply with your warranty!
Use of this product may cause your motorcycle to violate Federal Safety and/or Emission laws!

Rockland County Motorcycle is not responsible for any consequential damage to you or your motorcycle due to the use of this product!
This product will provide improved throttle response!
Take time and get used to your added driveability!
This Product is for "Off Road" / "Race Use" only

Last edited by jeech; 01-11-2005 at 09:39 AM.
jeech is offline  
Sponsored Links
Advertisement
 
post #2 of 2 Old 01-10-2005, 10:07 PM
Administrator
 
YSR50's Avatar
 
Join Date: Apr 2004
Location: Chicago burbs
Posts: 6,673
Posting Frequency
Images: 32
 
Garage
Discuss this mod here: https://zx-10r.net/forum/showthread.php?p=67418

"Be who you are and say what you feel, because those who mind don't matter and those who matter don't mind."
--Dr. Seuss
YSR50 is offline  
Sponsored Links
Advertisement
 
 

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Kawasaki ZX-10R.net forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in











Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
MOD gone seriously FUBAR!!!!!!! SMBowen The ZX-10R 28 11-06-2004 09:34 AM
Ivan's TRE Mod.......... SP8 The ZX-10R 74 10-17-2004 12:21 AM
Plates & TRE installed... Ground Zero The ZX-10R 4 10-04-2004 11:16 PM
Installed Akra, TRE, PC and fan today BIKEMIKE The ZX-10R 5 10-02-2004 11:16 PM
Headlight Mod BIGRED12R The ZX-10R 3 05-18-2004 10:54 PM

Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome