help: pc3 wont power up! - Kawasaki ZX-10R.net
Reply
 
LinkBack Thread Tools Display Modes
post #1 of 19 Old 05-31-2007, 02:07 PM Thread Starter
inappropriate
 
hesaves0211's Avatar
 
Join Date: Dec 2005
Location: NY/NJ/NC
Posts: 7,728
Posting Frequency
Images: 67
           
Send a message via AIM to hesaves0211
help: pc3 wont power up!

i bought a used pc3 from a fellow member. when i tested the pc3 w the 9 volt it had no prob powering up and linking to my laptop were i could retrieve its current map. however, once plugged into the 10s harness it will not power up (flash its little lights) independently. worst yet when i would start the bike it would turn over then immediately cut the motor. the "FI" light is also illuminated during this time. i could twist the throttle to give it gas but that would only result in a mess of smoke and rough operation. when i removed the pc3 and reconnected everything as it was the bike will operate fine.
i removed the unit, inspected all pins and wires and reinstalled. no luck yet, same symptoms as my first attempt.

1ST GEN-10R 234hp/[email protected], GT2871RS, cometic gasket, tial bov/ex wastegate, BEGI FMU, WALBRO fuel pump,falicon clutch basket,race pak clutch,200/50 pilot,yana-shiki levers,.net wristband, WEGO III,PC3,GPR damper,cbr cals/Galfer SS brake lines,gp shift,1/5 throttle, 2NDARIES REMOVED <<click for how-to, *R.I.P D.J 10 Apr 04*

Last edited by hesaves0211; 05-31-2007 at 02:15 PM.
hesaves0211 is offline  
Sponsored Links
Advertisement
 
post #2 of 19 Old 05-31-2007, 02:10 PM
I really need to get out of the house
 
luckz88's Avatar
 
Join Date: Apr 2005
Location: Fairfax, Va
Posts: 11,157
Posting Frequency
Images: 10
           
Send a message via AIM to luckz88 Send a message via Yahoo to luckz88
unhoook everythign and put it back to stock and see if you bike starts and runs fine than...it may have been damaged in shipping

NESBA #88

Madness Racing wishes he could handle the power of a GSXR

All my homies left this site
luckz88 is offline  
post #3 of 19 Old 05-31-2007, 02:16 PM Thread Starter
inappropriate
 
hesaves0211's Avatar
 
Join Date: Dec 2005
Location: NY/NJ/NC
Posts: 7,728
Posting Frequency
Images: 67
           
Send a message via AIM to hesaves0211
i was afraid of that. isnt there a way to reset it?

1ST GEN-10R 234hp/[email protected], GT2871RS, cometic gasket, tial bov/ex wastegate, BEGI FMU, WALBRO fuel pump,falicon clutch basket,race pak clutch,200/50 pilot,yana-shiki levers,.net wristband, WEGO III,PC3,GPR damper,cbr cals/Galfer SS brake lines,gp shift,1/5 throttle, 2NDARIES REMOVED <<click for how-to, *R.I.P D.J 10 Apr 04*
hesaves0211 is offline  
Sponsored Links
Advertisement
 
post #4 of 19 Old 05-31-2007, 02:17 PM
GP Star
 
usman's Avatar
 
Join Date: Aug 2003
Location: Arlington, VA
Posts: 2,337
Posting Frequency
Images: 13
         
silly little thing, on the pc3... on plug goes right into the fuel rail, and the 2nd plug gets the connection to the old plug that was going to your fuel rail, i think its brown.

i know i was a retard. and did it wrong.. i plugged one forgot to plug the other and had the same FI light issue.



old man ran off on his wheelchair

theazzman.com (my blog)
usman is offline  
post #5 of 19 Old 05-31-2007, 02:32 PM Thread Starter
inappropriate
 
hesaves0211's Avatar
 
Join Date: Dec 2005
Location: NY/NJ/NC
Posts: 7,728
Posting Frequency
Images: 67
           
Send a message via AIM to hesaves0211
Quote:
Originally Posted by usman View Post
silly little thing, on the pc3... on plug goes right into the fuel rail, and the 2nd plug gets the connection to the old plug that was going to your fuel rail, i think its brown.

i know i was a retard. and did it wrong.. i plugged one forgot to plug the other and had the same FI light issue.
can you clearfy? i cant quite make out what your saying.

1ST GEN-10R 234hp/[email protected], GT2871RS, cometic gasket, tial bov/ex wastegate, BEGI FMU, WALBRO fuel pump,falicon clutch basket,race pak clutch,200/50 pilot,yana-shiki levers,.net wristband, WEGO III,PC3,GPR damper,cbr cals/Galfer SS brake lines,gp shift,1/5 throttle, 2NDARIES REMOVED <<click for how-to, *R.I.P D.J 10 Apr 04*
hesaves0211 is offline  
post #6 of 19 Old 05-31-2007, 02:45 PM
GP Rider
 
mjg68901's Avatar
 
Join Date: Jul 2006
Location: Nebraska
Posts: 1,763
Posting Frequency
Images: 17
     
Make sure you have the pc hooked up correctly is what he is saying. If the connectors are switched around or not plugged in correct this could be the result you are seeing.

http://www.racemph.com/

Heavenly Father, thank you for your Word which is the Truth that sets me free. Give me strength to separate myself from anything that does not honor You. In Jesus Name. Amen.
mjg68901 is offline  
post #7 of 19 Old 05-31-2007, 02:52 PM
GP Rider
 
mjg68901's Avatar
 
Join Date: Jul 2006
Location: Nebraska
Posts: 1,763
Posting Frequency
Images: 17
     
Try this....
http://www.kotiposti.net/strato/Power%20Commander.htm

http://www.racemph.com/

Heavenly Father, thank you for your Word which is the Truth that sets me free. Give me strength to separate myself from anything that does not honor You. In Jesus Name. Amen.
mjg68901 is offline  
post #8 of 19 Old 05-31-2007, 02:56 PM Thread Starter
inappropriate
 
hesaves0211's Avatar
 
Join Date: Dec 2005
Location: NY/NJ/NC
Posts: 7,728
Posting Frequency
Images: 67
           
Send a message via AIM to hesaves0211
Quote:
Originally Posted by mjg68901 View Post
if im not mistaking thats a second gen. im working w first gen. i dont think you can get mixed up i didnt see anyother harness but ill triple check

1ST GEN-10R 234hp/[email protected], GT2871RS, cometic gasket, tial bov/ex wastegate, BEGI FMU, WALBRO fuel pump,falicon clutch basket,race pak clutch,200/50 pilot,yana-shiki levers,.net wristband, WEGO III,PC3,GPR damper,cbr cals/Galfer SS brake lines,gp shift,1/5 throttle, 2NDARIES REMOVED <<click for how-to, *R.I.P D.J 10 Apr 04*
hesaves0211 is offline  
post #9 of 19 Old 05-31-2007, 03:02 PM
GP Rider
 
mjg68901's Avatar
 
Join Date: Jul 2006
Location: Nebraska
Posts: 1,763
Posting Frequency
Images: 17
     
What year are you working with? People have had problems getting the connectors swapped around. I believe this is the bike(2005) that the description was written off of.
http://www.kotiposti.net/strato/Wint...20-%202006.htm

Make sure your ground is good also.

http://www.racemph.com/

Heavenly Father, thank you for your Word which is the Truth that sets me free. Give me strength to separate myself from anything that does not honor You. In Jesus Name. Amen.

Last edited by mjg68901; 05-31-2007 at 03:05 PM.
mjg68901 is offline  
post #10 of 19 Old 05-31-2007, 03:10 PM Thread Starter
inappropriate
 
hesaves0211's Avatar
 
Join Date: Dec 2005
Location: NY/NJ/NC
Posts: 7,728
Posting Frequency
Images: 67
           
Send a message via AIM to hesaves0211
Click image for larger version

Name:	Rubbers%20removed.jpg
Views:	74
Size:	88.0 KB
ID:	36362
this is the two connectors i was working with.

1ST GEN-10R 234hp/[email protected], GT2871RS, cometic gasket, tial bov/ex wastegate, BEGI FMU, WALBRO fuel pump,falicon clutch basket,race pak clutch,200/50 pilot,yana-shiki levers,.net wristband, WEGO III,PC3,GPR damper,cbr cals/Galfer SS brake lines,gp shift,1/5 throttle, 2NDARIES REMOVED <<click for how-to, *R.I.P D.J 10 Apr 04*
hesaves0211 is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Kawasaki ZX-10R.net forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in











Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
wont start 10roller Performance and Tech 5 05-08-2007 06:44 PM
bike wont rev out streetfighter Performance and Tech 4 11-22-2006 08:02 PM
help power commander issues wont run properly red fi light is on streetfighter Performance and Tech 17 11-12-2006 01:56 PM
Anaconda...You wont believe it 'less you see it. hillcountry10r Pictures and Videos 25 04-20-2006 07:45 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome