|Topic Review (Newest First)|
|11-27-2016 05:06 PM|
I would run a longer wire for the PC5 but from what I have read the PC5 really doesn't do much without the auto tuner . In 2013 I installed a PC5 in my bike at that time they didn't have a listing for me to click on so I had to find one that was close to the map I needed then had it dynoed. I had my bike stolen 2 months ago so now I have a 2016 . I have decided to buy a ecu and have it flashed then and a exhaust pipe. My only problem is which flash to choose . From what I understand the flash will do more for the bike then the PC5 can ever do so for me it's a no brainer.
Sent from my SPH-L900 using Tapatalk
|10-04-2016 04:58 AM|
|Adel Al Shemari||
I removed the PC5 and the bike ran great.
Then I checked, and it appeared that the previous owner installed the wideband sensor instead of the OEM o2 sensor in the exhaust. So I decided to reinstall the PC5 without the autotune, and the bike ran just fine. Also, the USB port on the PC5 was damaged, to the previous owner leaving the cable plugged and the seat pushed against it, which damaged the USB port. I contacted Powercommander, they said it cannot be repaired, and I must send it in for evaluation either way. Shipping from Dubai to the US is $$.. So I went to a telephone repair shop, bought a USB mini port for 2$, opened the PC5, and replaced it myself. Now it is fully functional again :)
Although I still have the same issue, there is NO ROOM under the seat to leave the PC5 plugged in. Any tips?
|07-27-2016 03:23 PM|
|tukn20s||Ditch the pcv and get your ecu flashed. Had no problems since.|
|07-27-2016 02:14 AM|
|Adel Al Shemari||
Hello guys, new on the forum.
Bringing this issue up again.
Not sure if mine is the same, so maybe someone can point me in the right direction.
My bike runs fine at WOT, although as soon as I cruise on partial throttle between 3k rpm and 6k rpm, the bike starts to misfire or run lean or drops a cylinder. If I hold the throttle steady in 4th gear at say 5.5k rpm, it will start to decelerate and drops rpm, then suddenly come back to life.
I emailed PC tech and they suggested I upgrade to v0.1.10.6 which I did, although issue was still there.
It really makes the bike not fun to ride at all, and I am about to ditch the PC5 if I cannot resolve it.
Mods: Akra exhaust + PC5 + autotune
Any suggestions would really help.
I will try 1.6.10 and report back.
|03-13-2016 06:10 PM|
|Ride4life||I just bought a used PCV5 I really hope I don't have these problem|
|01-07-2016 07:36 PM|
|tukn20s||Got a new pcv from dynojet..after a few weeks problem came back again. Ditched the pcv and found a ecu on ebay with guhls flash..runs like a dream now with NO problems..|
|01-07-2016 03:24 PM|
Originally Posted by ZX10RArcher View Post
Has anyone tried out the firmware beyond 1.9.2? about to install the PCV in my gen4 with a few other mods that have been a long time coming and want to make sure which firmware to throw in. Thanks guys
|07-20-2015 05:01 AM|
|peterj59||thanks for the updates|
|05-28-2015 01:33 PM|
Figured I'd throw this out there to see if anyone can comment.
My bike appears to be dropping a cylinder under 5k-6k rpms and obviously seems low on power. Anything above that mark, and to the red line, it's running just fine. As the bike runs more and more, the problem recedes down below 3k rpm mark. The puzzling part is that my bike is not running a Bazzaz or PCV box. It has the Archer flash and that's it. I have been told different things, such as bad coil or even problems with valves. I am pretty puzzled at the moment and wanted to see what you guys think before I start pulling things apart. Thanks!
|05-28-2015 10:51 AM|
|BuckwildZX10R||My third gen is doing this whenever she wants to should I update the firmware?|
|This thread has more than 10 replies. Click here to review the whole thread.|