ZX10R Exhaust Servo Eliminator "How To" D.I.Y. Gen 1, 2, & 3 - Kawasaki ZX-10R.net
 1Likes
Reply
 
LinkBack Thread Tools Display Modes
post #1 of 99 Old 06-02-2012, 07:35 PM Thread Starter
Servo's Eliminatus ;)
 
hellsrazor's Avatar
 
Join Date: Jul 2008
Location: Gulf Coast of Mississippi
Posts: 6,795
Posting Frequency
Images: 23
           
ZX10R Exhaust Servo Eliminator "How To" D.I.Y. Gen 1, 2, & 3

This is my FREE SHAREWARE on "How to build your own servo eliminator"
For a Gen 1, 2, 3, ZX10R ONLY...
I figured it was time to update my old thread to make it a little easier for peeps to understand
"How To Build It Themselves".

Read the entire 1st post, it contains all information needed to do this.

1st. I bought my Electronic parts at Radio Shack (Free Plug for them)
All pictured in the 1st Pic. Part #'s are on them.
**Note** In the 3rd pic the capacitor says 16volt,
but you can use the 35VDC instead. Radioshack is out of the 16volt.

2nd. You will need, A Soldering Iron, Solder, Electrical Tape, Epoxy.

3rd. Tools Needed : Needle nose pliers, Wire Strippers.

4th. Remove your Exhaust Servo Motor from your bike,
Cut the wires off of it as close to the motor as possible.

5th. Cut the GREY wire off the back of the one connector leaving the RED on.
On the 3 wire connector, leave ONLY the Black & Yellow wire on it.

6th. Assemble the Capacitor and Resistors as pictured in Pic # 4.

Make sure the arrows on the capacitor are pointing
at the black wire.
The resistors direction do not matter.
DO NOT DEVIATE from diagram.
I assume NO responsibility for any damage

7th. Solder the resistors to the capacitor to keep them secure.
Solder the circuit to the wires. Follow the diagram.

8th. Set the completed circuit in the Epoxy tray and pour Epoxy.
When Epoxy is set, remove and trim any sharp edges.

9th. Wrap Epoxied circuit with Electrical Tape.

10th. Install on your bike and you are done.


Now, If you cannot do this yourself.
I can and will build one for you, just PM or email me at
gen1zx10r@gmail.com
This has been verified to work all Gen 1's, 2's, & 3's.
Does not work on Gen 4 ZX10R's or ZX6R's.. Sorry
I do however, build ones for the Gen 4 ZX10R and ZX6R & Z1000, Z750

Don
Attached Thumbnails
Click image for larger version

Name:	2.jpg
Views:	6229
Size:	105.3 KB
ID:	162008   Click image for larger version

Name:	3.JPG
Views:	6229
Size:	56.3 KB
ID:	162009   Click image for larger version

Name:	4.jpg
Views:	7661
Size:	103.6 KB
ID:	162010  
Attached Images
  

If your hair is short and nappy...
Afrosheen will make you happy.
Anyone remember that one from the 1970's ?

Last edited by hellsrazor; 01-06-2013 at 01:46 PM.
hellsrazor is offline  
Sponsored Links
Advertisement
 
post #2 of 99 Old 06-02-2012, 09:00 PM
WSB Rider
 
GA10R's Avatar
 
Join Date: May 2007
Location: Tokyo
Posts: 691
Posting Frequency
       
Great write up.
FYI, Amazon sells a 10pk of resistors for $0.98
GA10R is offline  
post #3 of 99 Old 06-02-2012, 09:06 PM
Post Whore
 
-Op-'s Avatar
 
Join Date: Jul 2011
Posts: 6,020
Posting Frequency
          
Quote:
Originally Posted by GA10R View Post
Great write up.
FYI, Amazon sells a 10pk of resistors for $0.98
just curious though, what does shipping cost on that?

08 ZX6R Radial M/C ZG Sport Touring Windscreen CBR600RR Calipers BMC Street Filter
GP Shift Pattern DIY Mod Fender Eliminator Kit 16/44 Gearing Euro Flushmount Signals
Gauge Cluster Color DIY ModSoupy's Fully Adjustable Lowering Links HEL Stainless Steel Braided Brake Lines
-Op- is offline  
 
post #4 of 99 Old 06-02-2012, 09:22 PM
WSB Rider
 
GA10R's Avatar
 
Join Date: May 2007
Location: Tokyo
Posts: 691
Posting Frequency
       
Quote:
Originally Posted by -Op- View Post
just curious though, what does shipping cost on that?
I went to check out and they won't ship these components overseas. Back to square one.
GA10R is offline  
post #5 of 99 Old 06-02-2012, 09:28 PM Thread Starter
Servo's Eliminatus ;)
 
hellsrazor's Avatar
 
Join Date: Jul 2008
Location: Gulf Coast of Mississippi
Posts: 6,795
Posting Frequency
Images: 23
           
Oh SNAP, I just realized your in Japan bro.

You need me to hook you up with some??

If your gonna do it yourself, I can send you the parts.

Or I can build a complete one for ya, let me know.
Simon Hunt likes this.

If your hair is short and nappy...
Afrosheen will make you happy.
Anyone remember that one from the 1970's ?

Last edited by hellsrazor; 06-02-2012 at 09:31 PM.
hellsrazor is offline  
post #6 of 99 Old 06-02-2012, 09:39 PM
WSB Rider
 
GA10R's Avatar
 
Join Date: May 2007
Location: Tokyo
Posts: 691
Posting Frequency
       
Quote:
Originally Posted by hellsrazor View Post
Oh SNAP, I just realized your in Japan bro.

You need me to hook you up with some??

If your gonna do it yourself, I can send you the parts.

Or I can build a complete one for ya, let me know.
Hellsrazor I may end up pming you for parts. Nobody will ship resistors here...even though they're probably made here anyway.
GA10R is offline  
post #7 of 99 Old 06-02-2012, 09:52 PM Thread Starter
Servo's Eliminatus ;)
 
hellsrazor's Avatar
 
Join Date: Jul 2008
Location: Gulf Coast of Mississippi
Posts: 6,795
Posting Frequency
Images: 23
           
Quote:
Originally Posted by GA10R View Post
Hellsrazor I may end up pming you for parts. Nobody will ship resistors here...even though they're probably made here anyway.
Not a problem bro, let me know.

Also, I now have complete units to where you don't have to send me your harness and wait on a turn around time.

They are extra shipping to Japan.
Unless you are in the military and have an APO address,
and then it's like shipping inside the states.
If you aren't in the military, find a bud who is and ask him if you can ship to his APO address and save some $$$

If your hair is short and nappy...
Afrosheen will make you happy.
Anyone remember that one from the 1970's ?

Last edited by hellsrazor; 07-13-2012 at 01:47 PM.
hellsrazor is offline  
post #8 of 99 Old 06-04-2012, 12:25 AM
GP Star
 
Teeks's Avatar
 
Join Date: Apr 2010
Location: Green Bay Wi
Posts: 2,823
Posting Frequency
      
Quote:
Originally Posted by GA10R View Post
Hellsrazor I may end up pming you for parts. Nobody will ship resistors here...even though they're probably made here anyway.

I'm sorry, maybe its late or something, but I find that funny as hell

Hellrazor great write up, clear, and concise. Will be doing this project this week.

Thank you.

Quote:
Originally Posted by -Op- View Post
Unless Scout says dont do it. Then, really, just do it.
Quote:
Originally Posted by or10r View Post
I know its blistering fast but you cant outrun ugly.
Teeks is offline  
post #9 of 99 Old 06-04-2012, 01:14 AM Thread Starter
Servo's Eliminatus ;)
 
hellsrazor's Avatar
 
Join Date: Jul 2008
Location: Gulf Coast of Mississippi
Posts: 6,795
Posting Frequency
Images: 23
           
Quote:
Originally Posted by Teeks View Post
I'm sorry, maybe its late or something, but I find that funny as hell

Hellrazor great write up, clear, and concise. Will be doing this project this week.

Thank you.
Cool, post back up when you are done.
Glad it helped you bro.
I smile everytime someone doesn't have to pay $120 for an Ivans,
Or even $60 for the other one.

If your hair is short and nappy...
Afrosheen will make you happy.
Anyone remember that one from the 1970's ?
hellsrazor is offline  
post #10 of 99 Old 06-04-2012, 01:26 AM
Champion Rider
 
Join Date: Sep 2011
Location: NYC
Posts: 372
Posting Frequency
  
What does this actually do? Pretend I don't have a clue, only because it's the truth. What does the servo do? I have a 3rd gen with a slip on.

My experience with modern bikes is with an 03 z1000 so I'm not familiar with servos. Thanks for not flaming my non-knowledge.

enrico vespa is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Kawasaki ZX-10R.net forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome