Well, I have decided to go with a 16t front sprocket on my 08 ZX 10 :mrgreen:. Can someone chime in and tell me the part number that I need for the OEM replacement that may not be so noisy and or give a recommendation of brand to get. Thanks FC

Well, I have decided to go with a 16t front sprocket on my 08 ZX 10 :mrgreen:. Can someone chime in and tell me the part number that I need for the OEM replacement that may not be so noisy and or give a recommendation of brand to get. Thanks FC I tried an inexpensie Sunstar to see what it was like - not noisy at all, speedo error is about 11%.

I sprung for a slightly more expensive one than Sunstar, but not OEM. I have zero noise from my Driven sprocket setup and would higly recommend it. I was intimidated by all the hellish install experiences but after getting a breaker bar, socket, and extension install was a breeze. The two hardest parts were taking my bike to a ghetto mechanic and asking if I could use his impact wrench to crack the counter shaft nut off and scooping out all the factory chain lube from the sprocket cover. It took about 45 minutes from start to finish.

+1, I installed a Driven 520 driveset, very happy with it. I used an impact gun to remove the front nut, just make sure you leave the trans in neutral, very important! I bought my set from motomummy, it very easy. Select a brand, select front and rear tooth count and you can even choose from several different chains, + free shipping. I highly recommend a riveted master link instead of a clip. I dont trust the clip deal...

im running a vortex set front and back and a 520 chain i went with a 16t in front and a 41 in back like there stuff a lot

I also have a driven 16t on the way.....hope the install is as easy as everyone says :1848:

I also have a driven 16t on the way.....hope the install is as easy as everyone says :1848: Cake. PM me if you run into any problems...

I tried an inexpensie Sunstar to see what it was like - not noisy at all, speedo error is about 11%. I have a sunstar 16t and it whines so loud by friends make fun. They say it sounds like I have a supercharger or a jet engine. That's right before I turn on the afterburners and smoke em'. I have a new Driven 16t that I will be insalling this weekend Tony

im running a vortex set front and back and a 520 chain i went with a 16t in front and a 41 in back like there stuff a lot Thanks alot guys, our local stealership had a Vortex "Induction-Hardened Steel Countershaft Sprocket" chromoly one part # 2910-16T, so I bought it for 24.00 bucks and I am going to order the driven 16T and Speedo Healer from Motomummy just incase. So again, thanks for all the help, Ill keep you all posted on sounds and noises ect.... FC

get the front sprocket for a 2006 z100. being oem, it will last a while plus it has the rubber damping so it isnt loud. its a 16t.

get the front sprocket for a 2006 z100. being oem, it will last a while plus it has the rubber damping so it isnt loud. its a 16t. Thanks, will check it out.... that was a 06 Z1000 :thumbsup:

Thanks, will check it out.... that was a 06 Z1000 :thumbsup: yup, i had an 06 10 and that is what i used. now i have an 08 and looked up the front sprocket and it is the same part number as the 06...so im 100% sure the 06 z1000 sprocket will work.

I got a good deal and went a Rethal Took about 30 mins. to install.

:+1: to everyone that said Driven. I love their sprockets, good quality, good price, and fairly simple to install.

Well, I have decided to go with a 16t front sprocket on my 08 ZX 10 :mrgreen:. Can someone chime in and tell me the part number that I need for the OEM replacement that may not be so noisy and or give a recommendation of brand to get. Thanks FC you want to buy mine i have a driven 16 for zx10r sell it for $25 if you have paypal and $ 5 to ship so $30 total

you want to buy mine i have a driven 16 for zx10r sell it for $25 if you have paypal and $ 5 to ship so $30 total :+1: that looks like a good deal.

:+1: that looks like a good deal. Its new I assume?

I would hope so. I paid 26.00 for mine new.

so overall review of the 16T? I have one but haven't installed it yet because I'm giving Bikes (busa's, 1000's, fellow 14's) hell already. Usually from 50-70 then we take off (highways and back roads) Im scared ill loose my little edge since im not drag racing so i dont need that edge from 0-70. mostly roll ons. Im assuming ill still keep my edge but around 150-160 they'll start reeling me in with the 16T????

Its new I assume? yes with 50 miles or so .

I would hope so. I paid 26.00 for mine new. if you can prove you got it under $27 then i will lower it

if you can prove you got it under $27 then i will lower it My error mang... My sales reciept from Superbikesupply.com says 28.00.:sad: I don't know where the lack of 2.00 went??